Differences

This shows you the differences between two versions of the page.

--- docs:powercase-v1.9:start [2022/12/05 20:13]
admin
+++ docs:powercase-v1.9:start [2024/12/09 18:39] (current)
admin
@@ Line 1: / Line 1: @@
+===== OpenBuilds® PowerCase V1.9 =====
+{{:docs:powercase-v1.9:spin_powercase19.gif}}
+{{fa>shopping-cart}}   Order your [[https://openbuildspartstore.com/24v-meanwell-power-supply-bundle/|OpenBuilds PowerCase with 24v Meanwell PSU]]
+----
+===== Assembly Instructions =====
+----
 ==== 1.  NB: Set the 115/230v Switch ====
 Before connecting your power supply to mains power, it is critical that you check and set the 115v/230v Switch on the right-side of the PSU:
-{{:docs:powercase:meanwell-psu.png?400|}}
+{{:docs:powercase:meanwell-psu.png?400}}
 Look out for the bright yellow sticker on the top, to help you locate the switch:
-{{:docs:powercase:meanwell-sticker.png?200|}}
+{{:docs:powercase:meanwell-sticker.png?200}}
+----
 ==== 2.  Attach the Front Panel Spacers ====
 Using 3pc x M3x6mm Screws, attach the 3pc x M3x10mm Female/Female Hex Spacers to the Front Panel as shown
+{{:docs:powercase-v1.9:1_spacers_front_panel.png?600}}
-{{:docs:powercase-v1.9:1_spacers_front_panel.png?600|}}
+----
 ==== 3.  Attach the Front Panel to the Main Board ====
 Using another 3pc x M3x6mm Screws, attach the Main Board to the front panel by inserting the screws into the other end of the female spacers as shown.
-{{:docs:powercase-v1.9:2_dc_panel_spacer.png?600|}}
+{{:docs:powercase-v1.9:2_dc_panel_spacer.png?600}}
+----
 ==== 4.  Main Board / Front Panel assembly ====
@@ Line 25: / Line 43: @@
 Make sure your completed sub assembly matches the image below
-{{:docs:powercase-v1.9:3_sub_assembly_done.png?600|}}
+{{:docs:powercase-v1.9:3_sub_assembly_done.png?600}}
+----
 ==== 5.  Attach the Power Supply ====
 Loosen the terminals on the Meanwell LRS350-24 PSU.  Insert the mains wiring first:
-| Green Wire  | Earth  |
+|Green Wire    |Earth    |
-| White Wire | Neutral |
+|White Wire |Neutral |
-| Black Wire | Live |
+|Black Wire |Live |
 Make sure to tighten the terminal screws properly.
 Then proceed to slide the fingers of the main board under the terminals on the DC side of the Power Supply and tighten all the screws securely.
-{{:docs:powercase-v1.9:4_attach_to_psu.png?600|}}
+{{:docs:powercase-v1.9:4_attach_to_psu.png?600}}
+----
 ==== 6.  Attach the two Side Panels ====
 Using 2pc x M3 x 6mm and 2pc x M4 x 4mm screws, attach the two side panels as shown to the Power Supply and the Main board assembly.
-{{:docs:powercase-v1.9:5_side_panels.png?600|}}
+{{:docs:powercase-v1.9:5_side_panels.png?600}}
+----
 ==== 7.  Attach the Bottom Panel ====
@@ Line 51: / Line 75: @@
 Using 3pc x M3 x 6mm screws and 2pc x M4 x 4mm screws, attach the Bottom panel as shown
-{{:docs:powercase-v1.9:6_bottom_panel.png?600|}}
+{{:docs:powercase-v1.9:6_bottom_panel.png?600}}
+----
 ==== 8.  Attach the Top Panel ====
@@ Line 57: / Line 83: @@
 Using 3pc x M3 x 6mm screws attach the Top panel as shown
-{{:docs:powercase-v1.9:7_top_panel.png?600|}}
+{{:docs:powercase-v1.9:7_top_panel.png?600}}
+----
 ==== 9.  Attach the Mounting Panel ====
@@ Line 63: / Line 91: @@
 Using 2pc x M4 x 4mm screws attach the Mounting panel to the back of the Power Supply as shown
-{{:docs:powercase-v1.9:8_mounting_plate.png?600|}}
+{{:docs:powercase-v1.9:8_mounting_plate.png?600}}
+----
 ==== 10.  Complete! ====
@@ Line 70: / Line 99: @@
 Power on your creativity!
-{{:docs:powercase-v1.9:9_complete.png?600|}}
+{{:docs:powercase-v1.9:9_complete.png?600}}
+----
+===== Mounting Instructions =====
+----
+OpenBuilds® PowerCase V1.9 provides mounting holes on both ends that allows you to mount your power supply.
+Using M5 x 8mm Screws with M5 Drop-in Tee Nuts for mounting
+{{:docs:powercase-v1.9:10_mounting.png?600}}
+Attach to any V-Slot / C-Beam extrusion - for example one of our Tables
+{{:docs:powercase-v1.9:10_table.png?600}}

OpenBuilds Documentation

Differences

Page Tools