docs:powercase-v1.9:start
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
docs:powercase-v1.9:start [2022/12/05 20:12] admin |
docs:powercase-v1.9:start [2024/12/09 18:39] (current) admin |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | ===== OpenBuilds® PowerCase V1.9 ===== | ||
| + | |||
| + | {{: | ||
| + | |||
| + | {{fa> | ||
| + | |||
| + | ---- | ||
| + | |||
| + | ===== Assembly Instructions ===== | ||
| + | |||
| + | ---- | ||
| + | |||
| ==== 1. NB: Set the 115/230v Switch ==== | ==== 1. NB: Set the 115/230v Switch ==== | ||
| Before connecting your power supply to mains power, it is critical that you check and set the 115v/230v Switch on the right-side of the PSU: | Before connecting your power supply to mains power, it is critical that you check and set the 115v/230v Switch on the right-side of the PSU: | ||
| - | {{: | + | {{: |
| Look out for the bright yellow sticker on the top, to help you locate the switch: | Look out for the bright yellow sticker on the top, to help you locate the switch: | ||
| - | {{: | + | {{: |
| + | |||
| + | ---- | ||
| ==== 2. Attach the Front Panel Spacers ==== | ==== 2. Attach the Front Panel Spacers ==== | ||
| - | Using 3pc x M3x6mm Screws, attach the 3pc x M3x10mm Female/ | + | Using 3pc x M3x6mm Screws, attach the 3pc x M3x10mm Female/ |
| - | {{: | + | {{: |
| + | |||
| + | ---- | ||
| ==== 3. Attach the Front Panel to the Main Board ==== | ==== 3. Attach the Front Panel to the Main Board ==== | ||
| - | Using another 3pc x M3x6mm Screws, attach the Main Board to the front panel by inserting the screws into the other end of the female spacers as shown. | + | Using another 3pc x M3x6mm Screws, attach the Main Board to the front panel by inserting the screws into the other end of the female spacers as shown. |
| + | |||
| + | {{: | ||
| - | {{: | + | ---- |
| ==== 4. Main Board / Front Panel assembly ==== | ==== 4. Main Board / Front Panel assembly ==== | ||
| Line 25: | Line 43: | ||
| Make sure your completed sub assembly matches the image below | Make sure your completed sub assembly matches the image below | ||
| - | {{: | + | {{: |
| + | |||
| + | ---- | ||
| ==== 5. Attach the Power Supply ==== | ==== 5. Attach the Power Supply ==== | ||
| - | Loosen the terminals on the Meanwell LRS350-24 PSU. Insert the mains wiring first: | + | Loosen the terminals on the Meanwell LRS350-24 PSU. Insert the mains wiring first: |
| - | | Green Wire | Earth | | + | |Green Wire |Earth |
| - | | White Wire | Neutral | | + | |White Wire |Neutral | |
| - | | Black Wire | Live | | + | |Black Wire |Live | |
| - | Make sure to tighten the terminal screws properly. | + | Make sure to tighten the terminal screws properly. |
| - | Then proceed to slide the fingers of the main board under the terminals on the DC side of the Power Supply and tighten all the screws securely. | + | Then proceed to slide the fingers of the main board under the terminals on the DC side of the Power Supply and tighten all the screws securely. |
| - | {{: | + | {{: |
| + | |||
| + | ---- | ||
| ==== 6. Attach the two Side Panels ==== | ==== 6. Attach the two Side Panels ==== | ||
| - | Using 2pc x M3 x 6mm and 2pc x M4 x 4mm screws, attach the two side panels as shown to the Power Supply and the Main board assembly. | + | Using 2pc x M3 x 6mm and 2pc x M4 x 4mm screws, attach the two side panels as shown to the Power Supply and the Main board assembly. |
| - | {{: | + | {{: |
| + | |||
| + | ---- | ||
| ==== 7. Attach the Bottom Panel ==== | ==== 7. Attach the Bottom Panel ==== | ||
| - | Using 3pc x M3 x 6mm and 2pc x M4 x 4mm screws, attach the Bottom panel as shown | + | Using 3pc x M3 x 6mm screws |
| - | {{: | + | {{: |
| + | |||
| + | ---- | ||
| ==== 8. Attach the Top Panel ==== | ==== 8. Attach the Top Panel ==== | ||
| - | Using 3pc x M3 x 6mm attach the Top panel as shown | + | Using 3pc x M3 x 6mm screws |
| + | |||
| + | {{: | ||
| - | {{: | + | ---- |
| ==== 9. Attach the Mounting Panel ==== | ==== 9. Attach the Mounting Panel ==== | ||
| - | Using 2pc x M4 x 4mm attach the Mounting panel to the back of the Power Supply as shown | + | Using 2pc x M4 x 4mm screws |
| - | {{: | + | {{: |
| + | ---- | ||
| ==== 10. Complete! ==== | ==== 10. Complete! ==== | ||
| Line 70: | Line 99: | ||
| Power on your creativity! | Power on your creativity! | ||
| - | {{: | + | {{: |
| + | |||
| + | ---- | ||
| + | |||
| + | ===== Mounting Instructions ===== | ||
| + | |||
| + | ---- | ||
| + | |||
| + | OpenBuilds® PowerCase V1.9 provides mounting holes on both ends that allows you to mount your power supply. | ||
| + | |||
| + | Using M5 x 8mm Screws with M5 Drop-in Tee Nuts for mounting | ||
| + | |||
| + | {{: | ||
| + | |||
| + | Attach to any V-Slot / C-Beam extrusion - for example one of our Tables | ||
| + | |||
| + | {{: | ||
| + | |||
docs/powercase-v1.9/start.1670271148.txt.gz · Last modified: 2024/08/05 15:15 (external edit)