OpenBuilds Documentation

Part Store Documentation Software Community Support
docs:blox:firmware-arduino

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
docs:blox:firmware-arduino [2024/08/14 20:37]
admin 		docs:blox:firmware-arduino [2024/08/19 17:38] (current)
admin
Line 1: Line 1:
-======4.2 Arduino IDE Setup======+====== 5.2 Using BLOX with the Arduino IDE ======
  
 The Arduino IDE provides a flexible and powerful environment for programming BLOX devices using traditional code-based methods. This guide will help you get started by installing the Arduino IDE, setting up the ESP32 cores, and adding the necessary libraries. The Arduino IDE provides a flexible and powerful environment for programming BLOX devices using traditional code-based methods. This guide will help you get started by installing the Arduino IDE, setting up the ESP32 cores, and adding the necessary libraries.
  
-=====4.2.1 Requirements=====+---- 
 + 
 +===== 5.2.1 Requirements =====
  
 Before getting started, ensure that you have the following: Before getting started, ensure that you have the following:
  
-- A computer running Windows, macOS, or Linux. +  * A computer running Windows, macOS, or Linux. 
-- An internet connection to download the necessary software and libraries.+  * An internet connection to download the necessary software and libraries. 
 + 
 +---- 
 + 
 +===== 5.2.2 Installing Arduino IDE 2 ===== 
 + 
 +**Download Arduino IDE 2**: 
 + 
 +Visit [[https://www.arduino.cc/en/software|https://www.arduino.cc/en/software]] and select the appropriate version for your operating system. 
 + 
 +**Install the IDE**: 
 + 
 +Follow the installation instructions provided on the website. Once the installation is complete, launch the Arduino IDE. 
 + 
 +---- 
 + 
 +===== 5.2.3 Installing the ESP32 Cores ===== 
 + 
 +**Open the Arduino IDE**: 
 + 
 +Launch the Arduino IDE and navigate to `File > Preferences`. 
 + 
 +**Add the ESP32 Board URL**: 
 + 
 +In the "Additional Boards Manager URLs" field, enter the following URL: 
 + 
 +> [[https://raw.githubusercontent.com/espressif/arduino-esp32/gh-pages/package_esp32_index.json|https://raw.githubusercontent.com/espressif/arduino-esp32/gh-pages/package_esp32_index.json]] 
 + 
 +Click "OK" to save the preferences. 
 + 
 +**Install the ESP32 Core**: 
 + 
 +Go to `Tools > Board > Boards Manager`. 
 + 
 +In the search bar, type "ESP32" and install the latest version of the ESP32 by Espressif Systems. 
 + 
 +---- 
 + 
 +===== 5.2.4 Installing the OpenBuilds BLOX Library ===== 
 + 
 +**Open the Library Manager**: 
 + 
 +Go to `Sketch > Include Library > Manage Libraries`. 
 + 
 +**Search for the BLOX Library**: 
 + 
 +In the Library Manager, search for "OpenBuilds BLOX". 
 + 
 +Click "Install" to add the library to your Arduino IDE. 
 + 
 +Alternatively, you can install the library manually by downloading it from the [[https://github.com/OpenBuilds/OpenBuildsBLOX/|https://github.com/OpenBuilds/OpenBuildsBLOX/]] 
 + 
 +---- 
 + 
 +===== 5.2.5 Getting Started with BLOX on Arduino IDE ===== 
 + 
 +**Select the ESP32-S3 Board**: 
 + 
 +Go to `Tools > Board` and select the ESP32-S3 Development board for your BLOX device. 
 + 
 +**Connect Your BLOX Device**: 
 + 
 +Connect the BLOX device to your computer via USB. Ensure the correct port is selected in `Tools > Port`. 
 + 
 +Also set: 
 + 
 +  * USB CDC On Boot = Enabled 
 +  * Flash Size = 8MB (64Mb) 
 + 
 +**Upload a Sketch**: 
 + 
 +You can now write or upload a sketch to your BLOX device. Use the examples provided in the BLOX library to get started quickly. Including the OpenBuildsBLOX.h library will help you initialise all the onboard hardware with ease 
 + 
 +{{:docs:blox:pasted:20240814-204154.png}} 
 + 
 +---- 
 + 
 +===== 5.2.6 Pinmap for custom firmware =====
  
-=====4.2.2 Installing Arduino IDE 2=====+If you are not planning on using our library to control the onboard devices as part of your code, you can use the Pin map below to get you started with your own code 
 +<code>
  
-1. **Download Arduino IDE 2**: +// WS2812 LEDs 
-   - Visit the [Arduino IDE download page](https://www.arduino.cc/en/software) and select the appropriate version for your operating system.+#define LED_PIN         48
  
-2. **Install the IDE**: +// RC Servo 
-   - Follow the installation instructions provided on the website. Once the installation is complete, launch the Arduino IDE.+#define PIN_SERVO       47
  
-=====4.2.3 Installing the ESP32 Cores=====+// Stepper 1 
 +#define DIR_1           8 
 +#define STEP_1          9 
 +#define ENABLE_1        10 
 +#define FAULT_1         11 
 +// Remember to setup MCP4725 I2C DAC (Addr 0x60) to set Stepper Driver Current
  
-1. **Open the Arduino IDE**: +// Stepper 2 
-   - Launch the Arduino IDE and navigate to `File > Preferences`.+#define DIR_2           12 
 +#define STEP_2          13 
 +#define ENABLE_2        14 
 +#define FAULT_2         15 
 +// Remember to setup MCP4725 I2C DAC (Addr 0x61) to set Stepper Driver Current
  
-2. **Add the ESP32 Board URL**: +// Limits Inputs 
-   - In the "Additional Boards Manager URLs" field, enter the following URL:+#define LIMIT_SENSOR_1  39 
 +#define LIMIT_SENSOR_2  40
  
-     ''https://raw.githubusercontent.com/espressif/arduino-esp32/gh-pages/package_esp32_index.json''+// Mosfets 
 +#define PIN_MOSFET1     41 
 +#define PIN_MOSFET2     42
  
-      +// Beeper 
-   - Click "OK" to save the preferences.+#define BUZZER_PIN      7
  
-3. **Install the ESP32 Core**: +// I2C 
-   - Go to `Tools > Board > Boards Manager`. +#define I2C_SDA         3 
-   - In the search bar, type "ESP32" and install the latest version of the ESP32 by Espressif Systems.+#define I2C_SCL         4
  
-=====4.2.4 Installing the OpenBuilds BLOX Library=====+// SPI 
 +#define SPI_MOSI        35 
 +#define SPI_MISO        37 
 +#define SPI_SCK         36
  
-1. **Open the Library Manager**: +// SD Card 
-   - Go to `Sketch > Include Library > Manage Libraries`.+#define SD_CS           5
  
-2. **Search for the BLOX Library**: +void setCurrent(float milliAmps) { 
-   - In the Library Manager, search for "OpenBuilds BLOX". +  // Calculate reference voltage: Convert milliAmps to mV output from DAC 
-   - Click "Install" to add the library to your Arduino IDE.+  float millivolt = milliAmps / 5.0 / 0.22;
  
-   Alternatively, you can install the library manually by downloading it from the [OpenBuilds BLOX GitHub repository](https://github.com/OpenBuilds/OpenBuildsBLOX/).+  // Map the millivolt value to the DAC range (0 to 3300 mV to 0 to 4096) 
 +  int dacValue = map(millivolt, 0, 3300, 0, 4096);
  
-=====4.2.5 Getting Started with BLOX on Arduino IDE=====+  // Your own logic here to apply the dacValue to the correct DAC to set the current 
 +}
  
-1. **Select the ESP32 Board**: +</code>
-   - Go to `Tools > Board` and select the appropriate ESP32 board for your BLOX device.+
  
-2. **Connect Your BLOX Device**: +----
-   - Connect the BLOX device to your computer via USB. Ensure the correct port is selected in `Tools > Port`.+
  
-3. **Upload a Sketch**: 
-   - You can now write or upload a sketch to your BLOX device. Use the examples provided in the BLOX library to get started quickly. 
  
docs/blox/firmware-arduino.1723667869.txt.gz · Last modified: 2024/08/14 20:37 by admin

Page Tools

All works Copyright © by OpenBuilds®, LLC
All rights reserved. This Documentation or any portion thereof including but not limited to (menu structures, images, layout, videos, graphical artwork, logos, names, trademarks, etc.) may not be reproduced or used in any manner whatsoever without the express written permission of OpenBuilds, LLC