Differences

This shows you the differences between two versions of the page.

--- docs:blox:connect-limit-switches [2024/08/06 12:10]
admin
+++ docs:blox:connect-limit-switches [2024/08/15 12:52] (current)
admin
@@ Line 1: / Line 1: @@
-===== 3.6 Connecting BLOX to Switches =====
+====== 2.6 Connecting BLOX to Switches ======
 | {{:docs:exclamation.png?60|}} | **IMPORTANT WARNING**: Note: Incorrect wiring can short V+ to GND causing damage to your controller: Double check wiring before powering on.  |
@@ Line 7: / Line 7: @@
 These inputs are also the best choice for all other kinds of switches like toggle, push, lever or relay switches.  The inputs are opto-isolated and can accept switch signals between 0 and 30v. It also has onboard noise filtering.  The filtering and opto-isolation makes these two inputs the ideal choice (if available) for any kind of switched input your project needs.   If they are both in use, you can use GPIO for additional switches.
-> TIP: Set the Limit Switch voltage as required:  [[docs:blox:jumper-limitswitchvoltage|Set Limit Switch Voltage Jumpers]]
+----
+===== 2.6.1 Switch Wiring =====
+| **BLOX Terminal** | **Device** |
+| GND | GND |
+| V+ | Power Input (Optional, for powered sensors, filtering or LEDs) |
+| SIG | NO/NC terminal of switch |
 | **Xtension Limit Switches** | **Lever Micro Switches** | **Inductive Sensors** | **Others** |
 | {{:docs:blox:pasted:20240805-171252.png}} | {{:docs:blox:pasted:20240805-171448.png}} | {{:docs:blox:pasted:20240805-171500.png}} | {{:docs:blox:pasted:20240805-171030.png}} |
+----
-penBuilds BLOX can provide power to your limit switches / panel switches / sensors / etc : Please use the jumpers to configure the voltage your endstops need: 5v (the default) would be suitable for most mechanical and optical switches. 24v would be great for inductive sensors. Check your endstops' datasheets to determine which voltage would suit them better.
+===== 2.6.2 Switch Voltage =====
+OpenBuilds BLOX can provide power to your limit switches / panel switches / sensors / etc : Please use the jumpers to configure the voltage your endstops need: 5v (the default) would be suitable for most mechanical and optical switches. 24v would be great for inductive sensors. Check your endstops' datasheets to determine which voltage would suit them better.
 > These jumpers are located underneath the top cover of the BLOX, remove a screw on one of the sides to remove the top cover
@@ Line 19: / Line 31: @@
 Limit 1's and Limit 2's voltages can each be set to individually as needed:
-{{:docs:blox:pasted:20240805-125547.png}}
+{{:docs:blox:pasted:20240805-125547.png?600}}
 Set the jumper according to the required voltage for the sensor / limit switches attached:
@@ Line 25: / Line 37: @@
 ==== 5V Endstops (Default) ====
-{{:docs:blox:pasted:20240805-125635.png}}
+{{:docs:blox:pasted:20240805-125635.png?200}}
 ==== 12-30V Endstops (Same as input supply voltage) ====
-{{:docs:blox:pasted:20240805-125356.png}}
+{{:docs:blox:pasted:20240805-125356.png?200}}
+----

OpenBuilds Documentation

Differences

Page Tools