docs:blackbox-x32:start
Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision | ||
|
docs:blackbox-x32:start [2022/08/19 17:27] 127.0.0.1 external edit |
docs:blackbox-x32:start [2024/09/09 15:17] (current) admin |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | {{: | + | {{: |
| - | {{fa> | + | {{fa> |
| ---- | ---- | ||
| - | ===== OpenBuilds® BlackBox Specifications ===== | + | |
| + | ===== OpenBuilds® BlackBox | ||
| * Plug and Play easy connections that work directly with the OpenBuilds® Xtension wiring ecosystem | * Plug and Play easy connections that work directly with the OpenBuilds® Xtension wiring ecosystem | ||
| - | | + | * 4 x High Powered |
| - | | + | * Up to 1/32nd Microstepping |
| - | * Auxiliary Serial Input for alternative connectivity expansion | + | * Build in Cooling solution / through airflow design |
| + | * Easy current adjustment | ||
| + | * Capable of full 2/3/4-axes motion control | ||
| + | * Dual configurable onboard Relays | ||
| + | * Router (Enable) and VFD Spindle (Direction, Enable, 0-10v) Supported | ||
| + | * PWM Output for Lasers | ||
| + | * Servo Output for Pen Plotters | ||
| + | * Up to 24v 5A Switched Output for Coolant or LED devices | ||
| + | * 3x Optocoupled Endstop Inputs with power supply (5/24v) suitable for passive or active mechanical, optical and inductive switches | ||
| + | * 1x Optocoupled XYZ Probe Input | ||
| + | * Door sensor input | ||
| * USB Interface for Plug and Play | * USB Interface for Plug and Play | ||
| - | * Power Switch (no more reaching for the power strip or unplugging) | + | * WIFI Support |
| - | * Easily reachable Current Adjustment Potentiometers | + | * SD Card Support |
| - | * All new high end Enclosure/ | + | * High performance 32 Bit Processor |
| - | * Built in cooling solution/ | + | * Easy V-Slot/ |
| - | * Easy V-Slot compatible | + | * Dimensions: 171mm (Mounting flange included) x 80mm x 36.4mm |
| - | * 3 x Endstop inputs with optional power output | + | * Supported by OpenBuilds CONTROL software and all major CAM workflows |
| - | * Endstop inputs are protected against high voltages to allow for use of 24v Inductive Sensors | + | * Powered by highly customizable and configurable GrblHAL Firmware |
| - | * XYZ Probe input | + | |
| - | * Up to 24v 5A switched output for coolant devices such as 24v DC pumps, solenoids, contactors, or Solid State Relays | + | ---- |
| - | * Input Power Polarity protection with indicator LED | + | |
| - | * 10 Amp Input Power Fuse | + | ===== FCC Information: |
| - | * LED Indicators USB Serial | Power | Polarity | Probe | Motors Enabled | 4x Fault indicators | Coolant, (Spindle/ | + | |
| - | * Stepper Driver Fault condition | + | This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: |
| - | * 5v PWM and 5v Direction Spindle Signals | + | |
| - | * 0-10v Analog Spindle Control Signal Output | + | * Reorient or relocate |
| - | * Slave Axis configurable as a slave X, Y or Z | + | * Increase the separation between the equipment and receiver. |
| - | * Door Interlock signal connector to allow machines with enclosures to pause/ | + | * Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. |
| - | * Up to 1/32 Microstepping (Defaulted to 1/8 for higher Torque) | + | * Consult the dealer or an experienced radio/TV technician |
| - | * Well planned locations of all connectors | + | |
| - | * Configurable Relay for generic use cases (Plasma trigger, Coolant Pumps, Spindle control, etc | + | The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction |
| + | |||
docs/blackbox-x32/start.1660930046.txt.gz · Last modified: 2024/08/05 15:15 (external edit)