OpenBuilds Documentation

Part Store Documentation Software Community Support
docs:blackbox-x32:layout

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
docs:blackbox-x32:layout [2022/08/24 19:50]
admin 		docs:blackbox-x32:layout [2024/08/05 15:15] (current)
Line 3: Line 3:
 ==== 1. Front Side ==== ==== 1. Front Side ====
  
-{{:docs:blackbox-x32:tour-front.png|600}}+{{:docs:blackbox-x32:tour-front.png?600|}}
  
   * a) USB LEDs: Flashes in Blue/Green to indicate serial data transmit/receive traffic   * a) USB LEDs: Flashes in Blue/Green to indicate serial data transmit/receive traffic
Line 9: Line 9:
   * c) Status LEDs   * c) Status LEDs
     * Door LED: On when the Door input signal is active     * Door LED: On when the Door input signal is active
-    * Tool On: Indicates the Tool is Enabled+    * Tool On: Indicates the Tool is Enabled (Also Relay1)  
 +    * Tool Rev: Indicated Tool Direction is reversed (Also indicates Relay2) 
     * Tool PWM: Shows the proprotional RPM or output power of the PWM/0-10v outputs     * Tool PWM: Shows the proprotional RPM or output power of the PWM/0-10v outputs
     * Coolant LED:  Shows status of the Coolant signal (M8 = on, M9 = off)     * Coolant LED:  Shows status of the Coolant signal (M8 = on, M9 = off)
     * Probe LED: Lights up when the Probe Input activates     * Probe LED: Lights up when the Probe Input activates
     * Motors Enabled LED:   Indicates when the firmware has the Motor Drivers Enabled. In Grbl Settings set $4=1 (required for BlackBox drivers to function correctly) and $1=255 (to keep motors always enabled)     * Motors Enabled LED:   Indicates when the firmware has the Motor Drivers Enabled. In Grbl Settings set $4=1 (required for BlackBox drivers to function correctly) and $1=255 (to keep motors always enabled)
-  * d) Reset Button:  Restarts the Firmware; Mode button used to put microcontroller into Bootloader mode+  * d) Mode and Reset Buttons:  Reset: Restarts the Firmware; Mode button used to put microcontroller into [[docs:blackbox-x32:faq-bootloader|Bootloader mode]]
   * e) Power LED: If the Power LED is Green: Power Input OK   * e) Power LED: If the Power LED is Green: Power Input OK
   * f) Current Adjustment:  Adjust stepper driver current, see Section [[docs:blackbox-x32:currentadjustment|2.2.1 Current Adjustment]]   * f) Current Adjustment:  Adjust stepper driver current, see Section [[docs:blackbox-x32:currentadjustment|2.2.1 Current Adjustment]]
Line 27: Line 28:
 ==== 2.  Left Side ==== ==== 2.  Left Side ====
  
-{{:docs:blackbox-x32:tour-left.png|600}}+{{:docs:blackbox-x32:tour-left.png?600|}}
  
   * a) USB: Port for connecting the controller to your computer   * a) USB: Port for connecting the controller to your computer
Line 50: Line 51:
 ==== 3.  Right Side ==== ==== 3.  Right Side ====
  
-{{:docs:blackbox-x32:tour-right.png|600}}+{{:docs:blackbox-x32:tour-right.png?600|}}
  
   * a) Probe Input: Connect to a Probe, see Section [[docs:blackbox-x32:connect-xyzprobe|3.5.1 OpenBuilds XYZ Probe Plus ]] and [[docs:blackbox-x32:connect-zprobe|3.5.2 OpenBuilds Z Touch Plate]]  as well as more information on [[docs:xyzprobe:start|XYZ Probe Plus Documentation]]   * a) Probe Input: Connect to a Probe, see Section [[docs:blackbox-x32:connect-xyzprobe|3.5.1 OpenBuilds XYZ Probe Plus ]] and [[docs:blackbox-x32:connect-zprobe|3.5.2 OpenBuilds Z Touch Plate]]  as well as more information on [[docs:xyzprobe:start|XYZ Probe Plus Documentation]]
   * b) Limit Switch Inputs: Connect Limit switches: See Section [[docs:blackbox-x32:connect-xtension-limit|3.4.1 OpenBuilds Xtension Limit Switches ]] and [[docs:blackbox-x32:connect-micro-limit|3.4.2 Micro Limit Switch Kit]]   * b) Limit Switch Inputs: Connect Limit switches: See Section [[docs:blackbox-x32:connect-xtension-limit|3.4.1 OpenBuilds Xtension Limit Switches ]] and [[docs:blackbox-x32:connect-micro-limit|3.4.2 Micro Limit Switch Kit]]
   * c) Stepper Motor Outputs: Connect motors: See Sections  [[docs:blackbox-x32:connect-nema17|3.2.1]], [[docs:blackbox-x32:connect-nema23|3.2.2]] and [[docs:blackbox-x32:connect-nema23-reversed-y2|3.2.3)]] for connection details, and [[docs:blackbox-x32:faq-identify-motor-coils|6.1 Identify Motor Coils]] for troubleshooting information   * c) Stepper Motor Outputs: Connect motors: See Sections  [[docs:blackbox-x32:connect-nema17|3.2.1]], [[docs:blackbox-x32:connect-nema23|3.2.2]] and [[docs:blackbox-x32:connect-nema23-reversed-y2|3.2.3)]] for connection details, and [[docs:blackbox-x32:faq-identify-motor-coils|6.1 Identify Motor Coils]] for troubleshooting information
docs/blackbox-x32/layout.1661370651.txt.gz · Last modified: 2024/08/05 15:15 (external edit)

Page Tools

All works Copyright © by OpenBuilds®, LLC
All rights reserved. This Documentation or any portion thereof including but not limited to (menu structures, images, layout, videos, graphical artwork, logos, names, trademarks, etc.) may not be reproduced or used in any manner whatsoever without the express written permission of OpenBuilds, LLC