docs:blackbox-x32:layout
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
docs:blackbox-x32:layout [2022/08/22 17:25] admin |
docs:blackbox-x32:layout [2024/08/05 15:15] (current) |
||
|---|---|---|---|
| Line 3: | Line 3: | ||
| ==== 1. Front Side ==== | ==== 1. Front Side ==== | ||
| - | {{: | + | {{: |
| - | * a) USB LEDs: Flashes in Red/Green to indicate serial data transmit/ | + | * a) USB LEDs: Flashes in Blue/Green to indicate serial data transmit/ |
| * b) Power Switch: Used to turn the Main Power off, can be used in case of an emergency to bring the machine to an immediate stop | * b) Power Switch: Used to turn the Main Power off, can be used in case of an emergency to bring the machine to an immediate stop | ||
| * c) Status LEDs | * c) Status LEDs | ||
| * Door LED: On when the Door input signal is active | * Door LED: On when the Door input signal is active | ||
| - | * Tool On: Indicates the Tool is Enabled | + | * Tool On: Indicates the Tool is Enabled |
| + | * Tool Rev: Indicated Tool Direction is reversed (Also indicates Relay2) | ||
| * Tool PWM: Shows the proprotional RPM or output power of the PWM/0-10v outputs | * Tool PWM: Shows the proprotional RPM or output power of the PWM/0-10v outputs | ||
| * Coolant LED: Shows status of the Coolant signal (M8 = on, M9 = off) | * Coolant LED: Shows status of the Coolant signal (M8 = on, M9 = off) | ||
| * Probe LED: Lights up when the Probe Input activates | * Probe LED: Lights up when the Probe Input activates | ||
| * Motors Enabled LED: | * Motors Enabled LED: | ||
| - | * d) Reset Button: Restarts the Firmware; Mode button used to put microcontroller into Bootloader mode | + | * d) Mode and Reset Buttons: |
| - | * e) Power LED: | + | * e) Power LED: If the Power LED is Green: Power Input OK |
| - | * If the Power LED is Green: Power Input OK | + | |
| - | * If the Power is Red: Power connected with incorrect polarity | + | |
| * f) Current Adjustment: | * f) Current Adjustment: | ||
| * g) Fault Indicators: Indicates a problem with the stepper driver on the relevant axis: The LED indicates | * g) Fault Indicators: Indicates a problem with the stepper driver on the relevant axis: The LED indicates | ||
| Line 29: | Line 28: | ||
| ==== 2. Left Side ==== | ==== 2. Left Side ==== | ||
| - | {{: | + | {{: |
| * a) USB: Port for connecting the controller to your computer | * a) USB: Port for connecting the controller to your computer | ||
| Line 36: | Line 35: | ||
| * b) 0-10v Calibration: | * b) 0-10v Calibration: | ||
| * Calibration: | * Calibration: | ||
| - | * c) AUX Serial: (Advanced feature) Refer to Section [[docs: | + | * c) Interface Port: For connecting |
| * d) Door Switch Input: (Advanced feature) Refer to Section [[docs: | * d) Door Switch Input: (Advanced feature) Refer to Section [[docs: | ||
| * e) Servo: Used for pen-plotter applications: | * e) Servo: Used for pen-plotter applications: | ||
| - | * f) Relay: Used as a Plasma trigger: See Section [[docs: | + | * f) Relays |
| - | * g) Toolhead Connector | + | * Relay 1: |
| - | * GND: | + | * Relay 2: |
| - | * PWM: 5V TTL PWM signal, straight from Grbl (M3 Sxxx where xxxx = scaled between value of [[https:// | + | * g) 0-10v Output: Typically |
| - | * DIR: | + | * h) Tool Enable: |
| - | * 0-10v: | + | * i) Tool PWM: 0-3.3v PWM signal reflecting tool rpm/power. Typically used a PWM signal for DC motor controllers, |
| - | * h) Coolant: General output, switchable with M8/M9, refer to Section [[docs: | + | * j) Coolant: General output, switchable with M8/M9, refer to Section [[docs: |
| - | * i) Fuse: Protection fuse for the power input | + | * k) Power Input: Connect to 24v Power Supply. Double check polarity before powering on. See Section [[docs: |
| - | * j) Power Input: Connect to 24v Power Supply. Double check polarity before powering on. See Section [[docs: | + | |
| Line 53: | Line 51: | ||
| ==== 3. Right Side ==== | ==== 3. Right Side ==== | ||
| - | {{: | + | {{: |
| * a) Probe Input: Connect to a Probe, see Section [[docs: | * a) Probe Input: Connect to a Probe, see Section [[docs: | ||
| * b) Limit Switch Inputs: Connect Limit switches: See Section [[docs: | * b) Limit Switch Inputs: Connect Limit switches: See Section [[docs: | ||
| * c) Stepper Motor Outputs: Connect motors: See Sections | * c) Stepper Motor Outputs: Connect motors: See Sections | ||
docs/blackbox-x32/layout.1661189141.txt.gz · Last modified: 2024/08/05 15:15 (external edit)