Differences

This shows you the differences between two versions of the page.

--- docs:blackbox-x32:connect-vfd [2025/04/30 13:19]
admin
+++ docs:blackbox-x32:connect-vfd [2025/04/30 13:53] (current)
admin
@@ Line 21: / Line 21: @@
 {{:docs:blackbox-x32:0-10v.png?600}}
-==== Generic wiring instructions: ====
+==== Generic VFD wiring instructions: ====
 {{:docs:blackbox-x32:blackbox_vfd_2025_draw.png?800|}}
-This example uses RELAY1 as the Tool Enable, RELAY2 as FWD/REV and the 0-10V Output as speed CONTROL to control the VFD's activation, direction and speed respectively
+This example uses RELAY1 as the Tool Enable, RELAY2 as FWD/REV and the 0-10V Output as speed CONTROL to control the VFD's activation, direction and speed respectively.
+Every VFD brand labels their inputs slightly differently, and they all have different parameters to essentially set up the same features, but as can be seen from the diagram above, and cross referencing your VFD manual, you should also be able to adapt to other VFDs as well - almost all VFDs accept a dry contact enable/fwd/rev signal, and analog voltage 0-10v speed signal.
 ==== Checkout our Forums for more information: ====
@@ Line 32: / Line 34: @@
 ^   ^VFD^Link|
-|{{:docs:blackbox-x32:vfd-huanyang.png?50}}|**Huanyang VFD** |[[https://openbuilds.com/threads/vfd-spindle-control-via-openbuilds-blackbox-controller-and-software.15167/|https://openbuilds.com/threads/vfd-spindle-control-via-openbuilds-blackbox-controller-and-software.15167/]]|
+|{{:docs:blackbox-x32:vfd-huanyang.png?50}}|**Huanyang VFD** |[[https://openbuilds.com/threads/vfd-spindle-control-via-openbuilds-blackbox-controller-and-software.15167/|https://openbuilds.com/threads/vfd-spindle-control-via-openbuilds-blackbox-controller-and-software.15167/]] - NOTE writeup is for the older BlackBox 4X - just adapt to new terminal position on BlackBox X32 |
-|{{:docs:blackbox-x32:vfd-yl620a.png?50}}|**YL620-A VFD** |[[https://openbuilds.com/threads/yl620-a-vfd-settings.15780/|https://openbuilds.com/threads/yl620-a-vfd-settings.15780/]]|
+|{{:docs:blackbox-x32:vfd-yl620a.png?50}}|**YL620-A VFD** |[[https://openbuilds.com/threads/yl620-a-vfd-settings.15780/|https://openbuilds.com/threads/yl620-a-vfd-settings.15780/]] - NOTE writeup is for the older BlackBox 4X - just adapt to new terminal position on BlackBox X32 |
-|{{:docs:blackbox-x32:vfd-a28015.png?50}}|**A2-8015 VFD** |[[https://openbuilds.com/threads/a2-8015-vfd-inverter-with-1-5kw-air-cooled-spindle.19447/|https://openbuilds.com/threads/a2-8015-vfd-inverter-with-1-5kw-air-cooled-spindle.19447/]]|
+|{{:docs:blackbox-x32:vfd-a28015.png?50}}|**A2-8015 VFD** |[[https://openbuilds.com/threads/a2-8015-vfd-inverter-with-1-5kw-air-cooled-spindle.19447/|https://openbuilds.com/threads/a2-8015-vfd-inverter-with-1-5kw-air-cooled-spindle.19447/]] - NOTE writeup is for the older BlackBox 4X - just adapt to new terminal position on BlackBox X32 |
-|{{:docs:blackbox-x32:vfd-h100.png?50}}|**H100 VFD** |[[https://openbuilds.com/threads/h100-vfd-220v-with-1-5kw-spindel-2-poles-air-cooled-with-black-box.19442/|https://openbuilds.com/threads/h100-vfd-220v-with-1-5kw-spindel-2-poles-air-cooled-with-black-box.19442/]]|
+|{{:docs:blackbox-x32:vfd-h100.png?50}}|**H100 VFD** |[[https://openbuilds.com/threads/h100-vfd-220v-with-1-5kw-spindel-2-poles-air-cooled-with-black-box.19442/|https://openbuilds.com/threads/h100-vfd-220v-with-1-5kw-spindel-2-poles-air-cooled-with-black-box.19442/]] - NOTE writeup is for the older BlackBox 4X - just adapt to new terminal position on BlackBox X32 and wire the Direction terminals via the Relays instead of direct GPIO |

OpenBuilds Documentation

Differences

Page Tools